fascias.com

Description: Corotherm Flat Security Glazing Sheet

Dimensions: 610mm x 1220mm x 4mm 

Notes: Pack of 2 sheets

Corotherm Flat
Light Transmission % DIN 5036 90%
Coefficient of Thermal Expansion m/m°K 6.7 x 10-5
Thermal Properties U Value W/m2°K 5.6 @ 3mm
Service Temperature Range -20°C - +100°C
Fire Performance Up to Class I (BS476 Part 7)
Note 2mm does not have a Fire Test Certificate

Description

Dimensions: 915mm x 1220mm x 4mm 

Notes: Pack of 2 sheets

Corotherm Flat
Light Transmission % DIN 5036 90%
Coefficient of Thermal Expansion m/m°K 6.7 x 10-5
Thermal Properties U Value W/m2°K 5.6 @ 3mm
Service Temperature Range -20°C - +100°C
Fire Performance Up to Class I (BS476 Part 7)
Note 2mm does not have a Fire Test Certificate

Description

Dimensions: 610mm x 1830mm x 4mm 

Notes: Pack of 2 sheets

Corotherm Flat
Light Transmission % DIN 5036 90%
Coefficient of Thermal Expansion m/m°K 6.7 x 10-5
Thermal Properties U Value W/m2°K 5.6 @ 3mm
Service Temperature Range -20°C - +100°C
Fire Performance Up to Class I (BS476 Part 7)
Note 2mm does not have a Fire Test Certificate

Description

Dimensions: 610mm x 1220mm x 6mm 

Notes: Pack of 2 sheets

Corotherm Flat
Light Transmission % DIN 5036 90%
Coefficient of Thermal Expansion m/m°K 6.7 x 10-5
Thermal Properties U Value W/m2°K 5.6 @ 3mm
Service Temperature Range -20°C - +100°C
Fire Performance Up to Class I (BS476 Part 7)
Note 2mm does not have a Fire Test Certificate

Description

Dimensions: 915mm x 1220mm x 6mm

Notes: Pack of 2 sheets

Corotherm Flat
Light Transmission % DIN 5036 90%
Coefficient of Thermal Expansion m/m°K 6.7 x 10-5
Thermal Properties U Value W/m2°K 5.6 @ 3mm
Service Temperature Range -20°C - +100°C
Fire Performance Up to Class I (BS476 Part 7)
Note 2mm does not have a Fire Test Certificate

Description

Dimensions: 610mm x 1830mm x 6mm 

Notes: Pack of 2 sheets

Corotherm Flat
Light Transmission % DIN 5036 90%
Coefficient of Thermal Expansion m/m°K 6.7 x 10-5
Thermal Properties U Value W/m2°K 5.6 @ 3mm
Service Temperature Range -20°C - +100°C
Fire Performance Up to Class I (BS476 Part 7)
Note 2mm does not have a Fire Test Certificate

Cutting
Carefully score the sheet until nearly halfway through and right up to the edges, using a cutting knife with a chisel-type blade, against a firm straight edge, clamping the sheet to avoid slipping. It is best to score the sheet on a firm flat surface, such as a kitchen table or uncarpeted floor. Place the sheet on a firm table, with the scored cutting line upwards and along the edge of the table, then apply even pressure downwards to break the sheet along the scored line. If any irregularities occur, they can be smoothed with an emery board or filing plane. N.B. It will not be possible to cut Corotherm Flat using this method. See sawing guidelines below.

Sawing
Ariel Glazing Sheets can be sawn, either singly or several sheets together. Use an electric jigsaw or a handsaw with a fine toothed blade at a shallow angle. Sawing is better than cutting and dividing if just a thin strip needs to be removed from a sheet. For cutting curves, use an electric jigsawwhich has a scrolling feature.

Drilling
Slow speed power drills or hand drills are both suitable for drilling Glazing Sheets and should  be used with a metal working bit. Prevent the drill point from skipping by marking the hole position with a bradawl or by applying a small piece of adhesive tape where the hole is to be made. Use light pressure and back the sheet with a piece of wood to help prevent the sheet from chipping where the drill bit emerges. Make holes 3mm larger than fixings to allow for thermal movement.

Fixing
Ariel Glazing Sheet can be fixed using suitable proprietary fasteners, jointing strips, adhesives and sealants. Leave 3mm clearance around the edges of the panels to allow for thermal movement. Do not remove the protective filmuntil the piece is ready to be fitted.

Corotherm Flat can be installed in most types of frames including PVC, wood and aluminium. The framing system must retain the sheet but allow for thermal movement. Only compatible sealants must be used, these include silicone, EPDM, neoprene or 'plasticiser free' chloroprene materials of proven performance. Please note that PVC gasketsare not suitable for use with polycarbonate.

Cleaning
Use Ariel 'Liteglaze' anti-static cleaner, also suitable for use with Styrene and Corotherm Flat. DO NOT USE glass cleaner or abrasives.

LITEGLAZE GLAZING STRIP
The Liteglaze Glazing Strip can fix Ariel's glazing materials from 2mm to 4mm as secondary glazing to an existing window frame. The double sided adhesive tape means it can be fixed to either wood or metal frames securely. For larger wooden windows it is recommended that the strip is screw fixed. The 'snap-in' cap makes installation both quick and easy. It is also suitable for fitting Styrene in internal situations e.g. internal door panels, wallpaper protection etc.

Thermal Expansion Allowance